英國GRIMM格林進口蒸發循環泵 UK GRIMM Imported evaporation circulating pump

英國GRIMM格林進口蒸發循環泵概述： ?  

          進口蒸發循環泵為大流量、低揚程的軸流泵，引進和消化英國格林同類產品的優點，對該產品進行優化設計，確保該產品的運行可靠性、經濟性、安全性。該泵采用國際通用標準制造，高效率、性能穩定、可靠、維修方便。該產品廣泛應用于化工、有色金屬、制鹽、輕工等行業。是蒸發、結晶、化工反應等工藝過程。專供磷銨、磷酸、真空制鹽、氧化鋁、燒堿、輕工等行業中蒸發器的強制循環用，也可作結晶器、反應器的循環泵。

英國GRIMM格林進口蒸發循環泵結構特點：
進口蒸發循環泵主要由葉輪、泵體、副葉輪、密封箱、中間支架、軸承箱部件、軸承等零件組成。
1、泵體中心支撐：與泵體地腳支撐式比，轉子熱對中性好。
2、懸臂式轉子：與雙支撐式相比，軸封數量減半，泵重量輕，外形尺寸小，檢修方便。
3、泵效率高、高效區寬：用改變?nèi)~片安裝角、改變轉速兩種方法，滿足用戶對流量、揚程的要求且使泵的運行工位在高效區內，節能效果顯著。
4、抗汽蝕性能好：適用于低液位蒸發器，大幅度降低蒸發廠房投資。也適用于泵入口側配置流體阻力大的加熱室的新型蒸發器(反循環蒸發器，雙加熱室串聯蒸發器)。
5、低速型：泵運轉平穩；過流部件磨損輕、壽命長；晶體破損度低，適合于蒸發結晶工藝。
6、后開門結構：不需要拆卸泵體進出口法蘭的管路連接，即可抽出轉子，檢修方便，迅速。
7、軸封：采用動靜結構組合體，保證泵在工作和靜止時不會泄露，動力密封采用副葉輪密封，靜密封采用填料密封和機械密封；機械密封又分為單端面和雙端面兩種，以供選用。
8、蒸發器無膨脹節：可供彈性泵底座或懸掛式泵，熱補償可靠，減少蒸發器投資。
9、整機可靠性高：泵軸強度高，軸承承載能力大，軸承座有水冷套，軸封壽命長，材質性能好，確保單機長期運行效果好。
10、傳動方式：
直聯：泵與電機用過繞性聯軸器直聯(代號D)。
皮帶傳送：通過三角皮帶傳動，改變轉速調節泵性能容易(代號V)。
減速器：通過減速箱降速，適用于大功率泵(代號G)。

英國GRIMM格林進口蒸發循環泵技術參數： 

流量：300-12000m3/h
揚程：2-5m
口徑：25-1000mm
轉速：380-980r/min
功率：4-200kw
工作壓力：1MPa
工作溫度：≤170℃
注：訂貨時用戶應提供詳細的數據表，根據要求的流量、揚程、介質特性，推薦合理的泵型號。

英國GRIMM格林進口蒸發循環泵應用范圍： 
*濕法磷酸濃縮器、磷銨料漿濃縮器介質的強制循環。
*鋁酸鈉堿液蒸發器介質的強制循環。
*含NaCL的燒堿蒸發器介質的強制循環。
*NaCL真發結晶器介質的強制循環。
*Na2SO4蒸發器介質的強制循環。 
*硫酸銅、硫酸鎳等蒸發結晶器介質的強制循環。 
*氯化銨工序冷析結晶器，鹽析結晶器氨母液的強制循環。
*蒸銨廢液回收工序，CaCL2蒸發器介質的強制循環。 
*黑液濃縮器介質的強制循環。 
*煙氣脫硫、焦化廠和化纖廠硫酸銨蒸發結晶器介質的強制循環。 
*酒精濃縮、檸檬酸蒸發、糖業蒸發等工位介質的強制循環。

UK GRIMM Imported evaporation circulating pump summary:

        Imported evaporation circulating pump with large flow and low lift axial flow pump, the advantages of the introduction and digestion of Britain's Green of similar products, to optimize the design of the product, ensure the product reliability, economy and security. The pump is made by international standard, with high efficiency, stable performance, reliable and convenient maintenance. The product is widely used in chemical, nonferrous metals, salt making, light industry and other industries. Evaporation, crystallization, chemical reactions and other processes. Forced circulation evaporator for ammonium phosphate, phosphoric acid, vacuum salt, aluminum oxide, caustic soda, light industry and other industries to use, also can be used as a circulating pump crystallizer, reactor.

UK GRIMM Imported evaporation circulating pump structure characteristics:

The imported evaporation circulation pump mainly consists of impeller, pump body, auxiliary impeller, sealing box, intermediate support, bearing box, bearing and other parts.

1. Pump body center support: with the pump body foundation support ratio, the rotor heat is neutral.

2. Cantilever rotor: compared with the double support type, the number of sealing shaft is halved, the pump is light in weight, small in size and easy to overhaul.

3. Pump efficiency, high efficiency zone width: with the change of blade installation angle, change the speed of two ways, to meet the user flow, lift requirements, and make the pump running position in the high efficiency zone, energy-saving effect is remarkable.

4. Anti cavitation performance is good: applicable to low level evaporator, greatly reduce the evaporation workshop investment. The utility model is also suitable for the new type evaporator (reverse circulation evaporator, double heating chamber series evaporator) arranged in the heating chamber with large fluid resistance at the inlet side of the pump.

5. Low speed type: the pump runs smoothly; the over-current parts wear less light and long service life; the crystal damage is low; it is suitable for evaporation crystallization process.

6. The back door structure: no need to remove the pump body import and export flange pipe connection, you can take out the rotor, easy maintenance, quick.

7. Seal: the combination of static structure, ensure the pump will not leak in the work and the static, dynamic seal with vice impeller seal static seal with packing seal and mechanical seal; mechanical seal is divided into single face and double end in two, for the selection.

8. The evaporator has no expansion joint: it can be used as the base of elastic pump or suspension pump. The heat compensation is reliable and the investment of evaporator is reduced.

9. High reliability of the whole machine: high strength of pump shaft, large bearing capacity of bearing, water bearing sleeve of bearing seat, long life of shaft seal, good material performance, ensure long term operation of single machine.

10. Drive mode:

Direct connection: pumps and motors with winding couplings (code D).

Belt transmission: through the V-belt drive, change the speed of the pump performance is easy (code V).

Reducer: through the reduction gearbox down speed, suitable for high-power pumps (code G).

UK GRIMM Imported evaporation circulating pump technical parameters:

Flow rate: 300-12000m3/h

Lift: 2-5M

Caliber: 25-1000mm

Speed: 380-980r/min

Power: 4-200kw

Working pressure: 1MPa

Working temperature: less than or equal to 170 DEG C

Note: when ordering, users should provide detailed data tables. According to the required flow rate, lift head and medium characteristics, reasonable pump models are recommended.

UK GRIMM Imported evaporation circulating pump application range:

* Forced circulation of wet phosphoric acid concentrator, ammonium phosphate slurry concentrator medium.

* Forced circulation of sodium aluminate lye evaporator medium.

* Forced circulation of the medium of caustic soda evaporator containing NaCL.

* NaCL the forced circulation of the real mold medium.

Forced circulation of *Na2SO4 evaporator medium.

* Forced circulation of the evaporating crystallizer in copper sulphate and nickel sulphate.

* Cold process crystallizer for ammonium chloride process and forced circulation of ammonia mother liquor in salting out crystallizer.

* Recycling process of ammonium nitrate waste liquid, forced circulation of CaCL2 evaporator medium.

* Forced circulation medium liquor concentrator.

* Forced circulation of the medium of ammonium nitrate evaporation crystallizer in coking plant and chemical fiber plant.

* Forced circulation of working medium such as alcohol concentration, citric acid evaporation, sugar evaporation, etc..